Quarry Tiled Floor Restored in Shop to Flat Conversion in Oxford

This ground floor flat in the City of Oxford had been converted from a shop which as you can imagine, was quite complex. One significant element involved in the conversation was the restoration of an old Quarry tiled floor which ran through the main hallway and had for many years been covered in a commercial linoleum covering.

When the linoleum covering was removed, the sheer amount of glue which had been used to affix it had completely ruined the appearance and condition of the Quarry tiles. There was also a lot of concrete in the bathroom, and our client was keen to have this removed in the hope that the tiles beneath were salvageable.

Quarry Tiled Floor Oxford Before Restoration Quarry Tiled Floor Oxford Before Restoration

Removing Concrete and Glue Stains from a Quarry Tiled Floor

My first task at the property was to deal with the adhesive. I covered the entire floor area with Tile Doctor Remove and Go and then covered it with a plastic sheet and leaving it to soak into the glue and break it down overnight. Remove and Go is powerful stripper with a long-dwell time, formulated to break down adhesives and paint stains, amongst other coatings.

I returned the next day and, removing the plastic sheeting, I scrubbed the floor with a carbon brush attached to a rotary floor scrubber to remove the huge glue deposits. I worked in sections, rinsing each area of the floor with water after it had been scrubbed. Once I had finished the entire floor there was still some glue remaining, so I covered it again with a solution of Remove and Go combined with Tile Doctor HBU Nanotech, which utilises nano-sized particles to get underneath tough stains, dissolve them, and lift them out. I left this solution on the floor for about two hours to dwell and scrubbed it again.

During the next day of work, I used a very coarse 100 grit diamond burnishing pad to manually grind away the remaining stubborn bits of glue. Paying attention to the bathroom, I used a 50-grit coarse milling pad followed up with a 100-grit diamond burnishing pad to do the same to the area of concrete.

The next part of the process was to use Tile Doctor Grout Clean Up to acid wash the floor. This was successful in removing the last bits of cement and the remaining residue of the glue. To complete the cleaning process, I then rinsed the floor with plenty of water and vacuumed up any soiled solution.

Sealing a Quarry Tiled Floor

I opted to leave the floor alone for a couple of days to fully dry off so that it could be sealed upon my return. This is crucial as any moisture or damp issues can damage the performance of the sealer and expose the floor to further ingrained dirt and staining.

To seal the floor, I used Tile Doctor Colour Grow. This is an impregnating sealer that also enhances the natural reddish shades in the Quarry. I applied two coats of the sealer, giving the floor the natural look matte finish the customer desired.

Quarry Tiled Floor Oxford After Restoration Quarry Tiled Floor Oxford After Restoration

The customer was very impressed with the results of this thorough restoration. She even left the following feedback:

“I cannot recommend this service enough. The Oxford Tile Doctor (Barry) was a superstar: he cleaned up the tiles in my hallway, which were covered in a very thick layer of glue, and removed concrete from the tiles. They now look superb and I’m really happy with the outcome. Barry was always on time, considerate, and kept me up to date. The quote for the job was exactly right. I would not hesitate to recommend him.”
 
 
Source: Quarry Tile Cleaning and Restoration in Oxfordshire

Putting New Life Into a Quarry Tiled Floor in Oxfordshire

Sometimes it isn’t until you’ve deep cleaned your tiles that you realise just how dirty they were to begin with. This was the case with my customer in Thame, in the south of Oxfordshire where I worked on a classic red and black Quarry tiled floor which was far from being in its best condition.

Quarry Tiled Floor Before Cleaning Thame

Cleaning Dirty Quarry Tiles

My starting point in the cleaning process was to mix a strong solution of Tile Doctor Pro Clean, which is the reliable, multi-purpose alkaline cleaner that is safe to use on tile, stone and grout. The solution was left to soak into the tiles for ten minutes before being scrubbed into the floor with a rotary floor machine fitted with a stiff brush.

Following this, I rinsed the floor with clean water and then proceeded to wash it with Tile Doctor Grout Clean Up. This is a concentrated phosphoric acid cleaner designed to remove efflorescence and other mineral deposits such as grout smears.

Finally, I rinsed the tiles again with water and Tile Doctor Neutral Tile Cleaner, which is a pH neutral solution, to neutralise the chemicals and leave the floor fresh and clean, ready to be sealed. The floor was left to dry overnight.

Sealing Quarry Tiles

The next day I returned to seal the floor after checking the tiles were dry. I opted to use two different sealers. The first was Tile Doctor Colour Grow, which is an impregnating sealer with the added effect of enhancing the natural colour in the stone. The second was Tile Doctor Seal & Go, a topical sealer that adds the high quality, durable sheen finish to the floor that the customer had requested.

I took the photograph below after sealing half the floor, it really shows the difference a sealer can make to a tiled floor.

Quarry Tiled Floor During Sealing

Here’s the photo of theQuarry tiled floorafter sealing the whole floor. As you can see, they now have a new lease of life, and they’ll be much easier for the customer to keep looking great in the future.

Quarry Tiled Floor After Cleaning Thame

 
 
Source: Quarry Tile and Grout Cleaning and Restoration Service in Oxfordshire

Restoring Quarry floor tiles previously covered in Carpet

This Quarry tiled floor at a house in Banbury had previously been covered in carpet which had been stuck to the floor with an adhesive when once removed left a stain of white marks all over the floor. The customer had taken the floor as far as they could so I got the call to complete the restoration.

Quarry Tiled Floor Banbury Before Cleaning

Restoring Quarry Tiles

The first process was to tape the newly papered wall to protect them from any splashes during the cleaning process. I then scrubbed in a dilution of Tile doctor Pro-Clean with the assistance of a rotary floor machine fitted with a black pad and then rinsed off the resultant slurry.

This process defiantly made an improvement but I can see more work would be needed so I then applied a mixture of Pro-Clean and HBU (Heavy Build-up Remover) to the floor and scrubbed this with a carbon brush attached to a rotary floor machine. This proved to be more effective removing the carpet glue marks so I then rinsed the floor with water and used my wet vacuum to remove the slurry. I then gave the floor a thorough rinse with water again using the wet vacuum to extract the solution afterwards.

To finish the cleaning of the floor and remove any grout smears and other minderal deposits I applied Tile Doctor Acid Gel to the floor; this was left to dwell for a short time before scrubbing in with a stiff brush and then rinsed away with more water and extracted again using the wet vacuum.

The last job of the day was to fill in some holes in the tiles with a colour matching resin filler.

Sealing a Quarry Tiled floor

I returned two days later and confirmed the floor was dry ready for sealing. To seal the floor I first applied a coat of Tile Doctor Colour Grow which is an impregnating seal that also enhances the colour of the stone. This leaves a Matt finish and I showed the client this as they was not sure what finish they wanted, after seeing this that wanted more shine to the floor so once dried I applied a couple of coats of Tile Doctor Seal & Go which is a topical sealer that gives a sheen finish to the floor.

Quarry Tiled Floor Banbury After Cleaning

The client was very pleased with the end result leaving this as feedback.

Our options were a completely new floor or renovate the existing quarry tiles. We were glad we chose renovation; the results are amazing and a lot less messy and expensive than a new floor!
 
 
Source: Quarry Tile and Stone Cleaning and Restoration Service in Oxfordshire

Putting the Shine Back on Quarry Tiles

Not too long ago I visited a client who had just moved into a lovely old cottage in Milton, Oxfordshire. She wanted to restore many of the antique features of the building, including a fantastic Quarry tiled floor in the kitchen.

Quarry is typically a robust, hard wearing stone, but in a high traffic area like a kitchen, the tiles will need regular maintenance. These tiles clearly hadn’t seen a thorough clean and fresh seal in a long time, and so I was called in to provide just that.

Quarry Tiled Kitchen floor Before Cleaning Milton

Deep cleaning an old Quarry tiled floor

On the first day of work, I gave the Quarry tiles a deep clean using a strong solution of Tile Doctor Pro-Clean and water. Pro-Clean is a versatile alkaline cleaner that also helps to break down any old and no longer effectual sealer remaining on the tiles.

The solution was applied evenly to the floor and left to dwell for half an hour, allowing time for it to seep into the stone to get underneath and lift out the ingrained dirt. I then removed the dirt by agitating the solution with a scrubbing pad fitted to a rotary floor scrubber. I worked in small sections at first, and gradually finished the entire floor.

After completing the initial clean, I rinsed away the soiled solution and vacuumed up the excess moisture using a wet-vac machine. I then scrubbed the floor an acid wash using a dilution of Tile Doctor Grout Clean-Up to remove grout smears and other mineral type deposits. The resulting solution was then removed in a similar fashion using a wet-vac.

The final step in the cleaning process was to rinse the floor with Tile Doctor pH Neutral Cleaner to remove any trace of product helps to tackle any remaining dirt and reset the pH balance of the tiles before sealing.

Sealing a Quarry tiled floor

After leaving the floor to dry overnight, I returned the next day to the house to seal the floor with Tile Doctor Seal & Go, a water-based topical sealer which gives the floor an aesthetically pleasing sheen and a robust surface seal.

Quarry Tiled Kitchen floor After Cleaning Milton

The photos demonstrate the results better than this short account can, needless to say the floor is now transformed.
 
 
Source: Quarry Tile Cleaning and Sealing service in Oxfordshire

Restoring Quarry Tiles covered in Glue and Lino

This house near Banbury was the tied accommodation for an old village police station from the days when the local bobby would live in the house next door. I’m sure the Quarry tiled floor had a rich history which no doubt contributed to its poor state and was eventually was covered up with linoleum which had been stuck to the tiles with adhesive. Recently however the house had been sold and redecorated and the new owner wanted the floor restoring to its former glory.

Quarry Tiles Before Restoration in Banbury

Restoring Quarry Tiles

I started by covering the floor with a dilution of Tile Doctor Remove & Go which was left to dwell for 20 minutes taking care to ensure it didn’t dry out; it was then scrubbed into the floor with a black pad attached to my Rocky floor machine. This process removed most of the glue on the floor so after removing most the slurry and inspecting the floor I could see it would be necessary to repeat the whole process again and get down on my hand and knees to scrape off the thicker parts of the glue.

Once the glue had been removed the floor it was rinsed with clean water which was then removed using a wet vacuum. The next process was to clean the dirt out of the pores of the tile using a dilution of Tile Doctor Pro Clean and warm water. Again the solution was left to soak into the tiles before scrubbing, rinsing and removing with the wet vacuum.

After a lunch break the surface of the floor was drying and I noticed that the tiles we’re going white which would need to be dealt with before sealing. Older floors tend not to have a damp proof course which can lead to damp rising up through the tile depositing white salts on the surface in the process. This problem is called efflorescence and to resolve the tiles needed to be treated with Tile Doctor Grout Clean Up which was scrubbed into the tiles and washed off as before. The floor was then vacuumed dry and then left so it could dry out completely.

Sealing a Quarry Tiled floor

I returned a couple of days later and the floor was dry and clean but looking rather dull; to put some life back in the floor it was going to need to be sealed. I first put a coat of Tile Doctor Colour Grow down which brought the colour back into the tiles plus this is a good sealer on its own as it impregnates the pores of the tile and makes a terrific base seal. To complete I followed up with a number of coats of Tile Doctor Seal & Go which Is a topical sealer that provided the shiny finish the customer wanted.

Quarry Tiles After Restoration in Banbury

The quarry tiled floor is now restored from what was once a very old neglected floor to a nice clean easy to maintain surface.
 
 
Source: Professional Tile, Stone and Grout maintenance service in Oxfordshire