Restoring Original Victorian Quarry Tiles

The following photos are from a property in Finedon, Wellingborough where like so many of my customers it seems the owner was in the middle of a full property restoration which included plans to bring the original Victorian hallway Quarry tiles back to life. Tile Doctor restores hundreds of Victorian floors across the UK every year so she gave us a call. I came round to take a look at the tiles and could see that the floor had been covered with Linoleum for many years which had been fixed with adhesive we was still evident on the tiles along with old wax based sealers which would need to be stripped off. In general the floor was now looking very dull and uncared for.

Victorian Quarry Tiled Floor Finedon Before

Cleaning Victorian Quarry Tiles

To remove the glue and restore the tiles a dilution of Tile Doctor Remove and Go was left to soak into the pores of the tile for twenty minutes before being brushed in with a rotary machine fitted with a black stripping pad. Once done the floor was rinsed down thoroughly with water and the remaining solution removed with a wet vacuum, this revealed a few areas that needed re-treating so the whole process was repeated until I was happy that the glue and old sealers were gone and the tile and grout was as clean as I could get it. This process took up much of the day and after using the wet vacuum again to get the floor as dry as possible I left a couple of fan dryers in place to assist with the drying.

Sealing Victorian Quarry Tiles

The floor was left for a few days so it could dry out thoroughly and then checked for dampness and remaining staining, the floor was dry but there were a few areas that needed further attention which were spot treated and then dried out with a hand drier. To protect it and make it easier to clean in the future the floor was then sealed by applying a number of coats of Tile Doctor Seal and Gof which added a nice light sheen finish to the look of the tile.

Victorian Quarry Tiled Floor Finedon After

 
 
Source: Tile, Stone and Grout Restoration in Northamptonshire

New Life Breathed Into Old Pub Quarry Tiles

This house in Brinkworth was once a pub so as you can imagine the quarry tiled floor has certainly seen some foot traffic and abuse over the years. The owner contacted us to see if they were able to keep it as a feature entrance hall so we carried out a test which went very well and they booked us to do the work straight away.

Cleaning and Sealing Quarry Tiles in Brinkworth Before

Cleaning Quarry Tiles

Due to the level of ingrained dirt we started by covering the floor in Tile Doctor Remove & Go which is a very strong product usually reserved for removing coatings such as sealers from tile. We let it dwell for 10-15 minutes before working it in with a black scrubbing pad attached to a rotary machine; we scrubbed the area making sure that we covered it thoroughly. At this point It became apparent that there were many pitted areas with ingrained dirt so the process was repeated using a nylon scrub brush attached to the rotary machine to help get into all the pitted tiles. We then went round scraping any adhesives, paint or existing seal with a Stanley scraper.

Once we were happy with the result we then removed the slurry with a wet vacuum and rinsed with cold clean water several times with the aid of a deck brush to make sure ALL trace of cleaning product was removed. This process took most of the day and made a significant improvement to the state of the floor which was still quite damp at this stage so we left for the evening agreeing to come back in three days’ time to give the floor sufficient time to dry.

Cleaning and Sealing Quarry Tiles in Brinkworth Cleaned

Sealing Quarry Tiles

Upon our return we used a damp meter in several areas to check the floor had dried, most sealers won’t take to a damp floor and you can get unexpected results so it’s important to check first. The test results were fine so we started sealing the floor using Tile Doctor Seal and Go which is a water based sealer that doesn’t give off a smell whilst its drying, it also adds a subtle sheen to the tile and enhance the look of the floor as well as protecting the tile from future staining.

Cleaning and Sealing Quarry Tiles in Brinkworth Sealed

 
 
Source: Tile, Stone and Grout Problems resolved in Wiltshire

Dealing With Efflorescence Problems

Efflorescence occurs when water rises up through the floor leaving salt deposits on the surface of the tile as it evaporates and can be a problem on old floors where there is no damp proof course. The photographs below of an old Quarry tiled floor at a house in Leicester are a great example of this, fortunately there is a solution and I’ll walk you through this in the story below.

Efflorescence on old Quarry tiles in Leicester

Removing Efflorescence from Quarry Tiles

The first step was to give the tiles and grout a good clean and then strip the floor of any remaining sealer for which I used a dilution of Tile Doctor Remove and Go which was applied to the floor and left to soak in for ten minutes before being scrubbed in with a rotary machine fitted with a black scrubbing pad. The now soiled solution was then removed using a wet vacuum and the floor rinsed with water.

To remove the efflorescence you need to acid wash the floor for which we use Grout Clean-Up which as its name suggests is normally reserved for removing grout smears from tiles however it’s also useful for removing mineral deposits such as the salts from efflorescence and even rust stains. The acid is scrubbed onto the floor just long enough for it to do its job and then quickly removed and the floor given a thorough wash with water, acids can damage a tiled floor if left on for too long so you do need to be careful.

Efflorescence removed from old Quarry tiles in Leicester

Sealing Quarry Tiles

Given there was no DPC the floor was left to dry off for a few days and when we returned it was sealed with several coats of Tile Doctor Colour Grow which gives the matt finish the customer wanted. Colour Grow is a penetrating sealer that provides stain protection by soaking deep into the pores of the Quarry tile and preventing dirt from becoming ingrained there, it also does a good job of enhancing the natural colour of the tile.
 
 
Source: Tile, Stone and Grout Problems resolved in Leicestershire

Stripping and Re-Sealing a Quarry Tile Floor

The photographs below are from a Quarry Tiled floor installed in the dining room of a house in Hinkley, Leicestershire. The tiles were look washed out and the sealer was failing in the high traffic areas leading to dirt becoming ingrained into the tile; the floor was now in need of a deep clean and re-seal.

Quarry Tiles Cleaned in Hinckley Before

Cleaning Kitchen Quarry Tiles

The first step was to strip the floor of any remaining sealer, to add more sealer on top of existing can lead to problems so a dilution of Tile Doctor Remove and Go was applied to the floor and left to soak for a short while before being scrubbed in with a rotary machine fitted with a black scrubbing pad. Remove and Go is a powerful stripper which is safe to use on Tile and as its name suggests it can remove coatings, it also does a good job in cleaning the floor at the same time. In the middle of this I also like to run a stiff brush along the grout lines as the floor pads don’t always reach into the grooves. The soiled cleaning solution was then removed using a wet vacuum and the floor thoroughly rinsed with water and then left to dry overnight.

Sealing Kitchen Quarry Tiles

When we returned the next day I checked for dampness and any ugly spots that would need further attention and once happy started with sealing. On this occasion four coats of Tile Doctor Colour Grow were applied; Colour Grow gives a matt finish and brings out the natural colours in the tile whilst providing stain protection by soaking deep into the pores of the Quarry tile and preventing dirt from becoming ingrained there.

Quarry Tiles Cleaned in Hinckley After

Source: Tile, Stone and Grout Cleaning Service in Leicestershire

Removing Glue from Quarry Tiles

This customer in Warninglid, near Cuckfield asked me to clean a Quarry tiled floor that had been hidden for years under carpet. The carpet had been thoroughly stuck down with glue and sticky gripper rods so the tiles were in quite a mess. Whilst I thought that most of the floor could be greatly improved I voiced my reservations about several patches of heavy glue and some blackened area where burning logs appeared to have rolled from the hearth onto the stone.

Old Quarry Tile Floor Warninglid Before Restoration Old Quarry Tile Floor Warninglid Before Restoration

Deep Cleaning Quarry Tiles

I spent several hours stripping and cleaning the floor using Tile Doctor Pro-Clean first with hand brush then buffer, but struggled to remove the glue around the edges which wouldn’t shift. The solution appeared to be using a hand scrapper and so after a full day of scrapping and rubbing the floor was clean and before I left I gave it a good rinse with water to remove any product. I left it to dry for a couple of days and then the day before I was meant to return to seal the tiles I got a call from the customer who was concerned that the glue marks were more apparent now the floor was dry. I was between jobs so I popped round to have a look and had to agree it seemed there was still evidence of glue on the floor. Something stronger was clearly needed so I spot cleaned with Tile Doctor Remove and Go which is a strong coatings remover that is safe to use on Tile and Stone. Whilst not removing the glue entirely it made a huge improvement and the customer was happy with the result. I washed the impacted areas and used a heat gun to get the tiles dry so I was still able to return the next day to seal them.

Sealing Quarry Tiles

I sealed the Quarry tiles with three coats of Tile Doctor Pro-Seal which adds a subtle finish to the floor and will provide the tiles with long lasting protection. Luckily the next day was quite warm and the room was well ventilated by several windows and a double door so the tiles dried quickly.

Old Quarry Tile Floor Warninglid After Restoration Old Quarry Tile Floor Warninglid After Restoration

As you can see from the photographs on this page, the floor was really transformed and needless to say the customer was very satisfied with the result.
 
 
Source: Tile, Stone and Grout Cleaning Service in Sussex

Removing Paint from Quarry Tiles

Details below of a Victorian Quarry tiled floor belonging to a customer in Oswestry who had recently moved back to the area and wanted to restore the original features of the house including the Quarry tiles floor which had several coats of red floor paint and was later was covered with carpet for a number of years. The customer described the floor as:

“I have 2 areas of quarry tiles that need a serious make over, in the hall and the back room. There are patches of red paint and areas of mineral deposit and lots of ingrained filth!””

Red Black Quarry Tiles Oswestry Before Red Black Quarry Tiles Oswestry Before

Cleaning a Quarry Tiled Floor

I managed to clean the floor with a strong dilution of Tile Doctor Remove and Go which was left to soak into the tiles for a while before being scrubbed in using a rotary machine fitted with a black pad; the resultant slurry was washed away using more water and a wet vacuum. The whole process was repeated several times as the paint was really stubborn and in places I had to remove the paint removal with a scraper. Once I was happy with the condition it was given a final rinse to remove any cleaning products and then left to dry for five days leaving an air mover with the customer to accelerate drying.

Red Black Quarry Tiles Oswestry After Cleaning Red Black Quarry Tiles Oswestry After Cleaning

Sealing a Quarry Floor Sealing

The tiles have to be dry before sealing and even though I returned five days later the damp meter still indicated that there was moisture in the tiles which I suspect was due to there being no membrane in place under the old Victorian tiles. I agreed with the customer to come back a further week later which proved sufficient and the floor was dry enough to take the sealer.

The customer wanted a matt finish so I sealed the floor with two coats of Tile Doctor Colour Grow which is an impregnating sealer that occupies the pores in the tile and also enhances the colour of the tile.

Red Black Quarry Tiles Oswestry After Sealing Red Black Quarry Tiles Oswestry After Sealing

The customer was out when I applied the sealer but when the she got home she sent me the following message:

“The floor looks brilliant. So much better than I had ever hoped. Thank you.”
 
 
Source: Tile, Stone and Grout Cleaning and Sealing in Surrey

Removing Cement and Mortar from Quarry tiles

The photographs below of a Red and Black Victorian Quarry tiled floor were taken at a 109 year old cottage in the town of Telford. Unfortunately the tiles were in a really neglected state after the completion of building works but we do like a challenge and agreed to do the work.

Victorian Quarry Tiles Telford before cleaning Victorian Quarry Tiles Telford before cleaning

Cleaning a Quarry Tiled Floor

The whole floor was covered in layers of mortar and plaster so a strong solution of Tile Doctor Remove and Go was applied and scrubbed into the floor using a rotary machine fitted with a black scrubbing pad.

The initial clean revealed a lot more of the mess that had been left over from the builders mixing of mortar and concrete so I decided to try an acid based product called Tile Doctor Grout Clean-Up which is mainly used for the removal of grout from the tile surface but works on other cementitious materials as well. This worked well but required several applications to remove it all and once complete the floor was given a thorough rinse with clean water to ensure it was clear of the resultant slurry and there was no trace of cleaning product. A wet vacuum was used to remove the water from the floor and get it dry so it could be sealed.

Sealing a Quarry Floor Sealing

Once the floor was dry I sealed it using two coats of Tile Doctor Colour Grow which was chosen as the customer wanted a matt finish; Colour Grow also brings out the colours in the tile and it’s an impregnating sealer that occupies the pores in the tile to provide excellent stain protection.

I think you will agree the photographs below shows an amazing transformation that exceeded all expectations.

Victorian Quarry Tiles Telford After cleaning Victorian Quarry Tiles Telford After cleaning

Source: Residential and Commercial Tile and Stone Restoration in Shropshire

Quarry Tiled Floor Hidden Under Ceramic Tiles Restored

The history of this Quarry Tiled floor at a house in Swindon is a little unusual in that the owner had discovered the Quarry tiles underneath cracked ceramic tiles which had been laid over the top for several years. The customer wanted to bring the Quarry tile back to life to match the existing hallway from the kitchen and so we got a call. Incidentally the practice of laying new tiles on top of old is not unusual as an existing tiled floor provides an ideal level on which to lay new tiles.

Quarry Tiles Swindon Before Cleaning Quarry Tiles Swindon Before Cleaning

Cleaning Quarry Tiles

We started by using a floor scraper to scrape off as much tile adhesive as possible. Once this was done we mixed a strong dilution of Tile Doctor Grout Clean-Up and brushed it all over the remaining tile adhesive and used a black scrubbing pad attached to a rotary machine to remove the glue. This took several attempts using more Grout Clean-up, a floor scraper and a black scrubbing pad to remove all traces of the adhesive. Next we rinsed off any trace of product using clean water and then removed it using a wet vacuum.

The floor was free of glue at this point but we still needed to remove any existing sealer from the tiles and give them a deep clean to remove ingrained dirt so a strong solution of Tile Doctor Pro-clean mixed 50/50 with Nanotech Ultraclean was applied to the tiles and left to dwell for twenty minutes. (The Nanotech product adds tiny abrasive particles to the mix making a more effective cleaner). The solution was worked into the tile using a black pad attached to a rotary machine and the floor thoroughly scrubbed. Once satisfied the tiles were rinsed with clean water several times to remove any trace of cleaning product and the water removed using a wet vacuum. A lot of work had gone into the floor at this point and it needed time to dry before sealing so we left for the evening.

Sealing Quarry Tiles

We returned two days later and after testing the tiles were dry using a damp tester, which came back as OK, we processed to seal the Quarry tiles using six coats of Tile Doctor Seal and Go which is an ideal sealer for Quarry tiles as it adds a nice sheen to the floor as well as providing future surface protection. Seal and Go is also water based so there’s no smell as it dries.

Quarry Tiles Swindon After Cleaning Quarry Tiles Swindon After Cleaning

Source: Residential and Commercial Tile, Stone and Grout Restoration in Wiltshire

Removing Varnish from Quarry Tiles

We were asked to take a look at these Quarry Tiles at a house in the Lancashire town of Formby near Liverpool. The tiles had been sealed with varnish but a polyurethane sealer like Varnish which forms a thin coat on the surface of the tile is easily scratched as you can see in the photograph below:

Varnished Quarry Tiles Cleaning Formby Before

Cleaning Quarry Tiles

To resolve the problem we had to strip off the Varnish coating from the Quarry tile using Tile Doctor Remove and Go which is especially designed for the safe removal of coatings from tile and stone. The product is diluted and spread over the floor allowing it to soak into the tile for around fifteen minutes before being scrubbed into the tile using a rotary floor scrubbing machine fitted with a black pad. The soiled solution is then washed off with clean water and extracted from the floor using a wet vacuum. There were some stubborn areas and these were tackled by repeating the process but this time with the addition of a steamer.

A stiff brush was also used in the grout lines and when we were completely satisfied with the condition of the floor it was given an thorough rinse using cold water. The wet vacuum was used again to remove the water and get the floor as dry as possible.

Varnished Quarry Tiles Cleaning Formby After Cleaning

Sealing Quarry Tiles

The floor was left to dry overnight and we came back the next day to seal the floor using four coats of Tile Doctor Seal and Go which will protect it going forward and it also adds a nice shine to the tile.

Varnished Quarry Tiles Cleaning Formby After Sealing

 
 
Source: Residential and Commercial Tile Cleaning Services in Lancashire

Removing a Sealer From Kitchen Quarry Tiles

I recently paid a free home survey visit to a home owner in the village of Sherston near Malmesbury where the sealer on her Quarry Tiled Floor had started to fail in places and was becoming difficult to keep clean. Whilst I was there I did a sample clean and after reviewing the results she was happy to book us in for the job.

Quarry Tiles in Sherston Before Cleaining

Cleaning Quarry Tiles

To clean the Tiles and strip off the remaining sealer we used a strong dilution of Tile Doctor Pro-clean mixed 50/50 with Nanotech Ultraclean, the Nanotech product adds tiny abrasive particles to the mix making it a more effective cleaning product. This was left to dwell on the floor for twenty minutes before being worked into the tile using and black buffer pad fitted to a rotary buffing machine. The whole area was cleaned in this manner along with a stiff hand brush to get into the grout lines and a wet vacuum which was used to suck up the dirty residue before the floor was rinsed down with cold water.

Once the floor had started to dry it had become apparent that there was still some seal left behind. To resolve this problem I used Tile Doctor Remove and Go which is a powerful coatings remover product. It was left to dwell on the Quarry tiles for ten minutes before being scrubbed in with both a deck brush and black pad. I was still having problems removing all the seal so I then used a steamer with Remove and Go and a stiff deck brush to remove the last of the evident seal. The floor was then thoroughly rinsed the floor several times with clean water to remove any product build up and the ware removed using the wet vacuum.

Sealing Quarry Tiles

The floor was left to dry for a couple of days and then I returned to seal the floor first testing it was dry with a damp meter. The floor was fully dry we applied multiple coats of Tile Doctor Seal and Go which will protect the floor from stains going forward making it easier to clean and also adds a nice shine to the tile.

Quarry Tiles in Sherston After Cleaining
Before leaving I advised the customer on the use of a Neutral tile cleaner to help prolong the life of the sealer, there are a number of acidic floor cleaning products available which should not be used with stone or sealed floors as the acid will eat into the sealer over time reducing its life.

Source: Residential and Commercial Tile Cleaning Services in Wiltshire

Careful Cleaning of Quarry tiles around a swimming pool

Photographs below of a job we did cleaning and sealing the Quarry Tiles surrounding a residential indoor swimming pool floor tiles at a grand residence in Cambridge. As you can see from the photograph below the Quarry tiles and Grout was looking rather washed out and given their proximity to the pool extra care was needed to be ensure we didn’t contaminate the pool with dirty water from the cleaning process or chemicals, fortunately all our equipment is electrically isolated so that was not a problem.

Quarry Tiled Pool Surround Cambridge Before Cleaning Quarry Tiled Pool Surround Cambridge Before Cleaning

Swimming Pool Tile Cleaning

Fortunately the pool was fitted with a cover so we made a start cleaning the tiles using a strong dilution of Tile Doctor Pro-Clean mixed 50/50 with NanoTech Ultra Clean which add tiny abrasive particles into the cleaning solution making it more effective. Working in sections the solution was left to soak into the tile and grout before being worked into the floor using a rotary machine fitted with a scrubbing pad running at slow speed to reduce splashing. This process removed any remaining sealer and cleaned the tile and grout up nicely, we used clean water to rinse the floor and a wet vacuum to remove the soiled solution making sure not to drain any solutions into the pool and re-treating any stubborn areas. This process was fairly tedious and took up much of the day but the results were well worth the effort.

Quarry Tiled Pool Surround Cambridge After Cleaning Quarry Tiled Pool Surround Cambridge After Cleaning

Sealing Quarry Tiles around a Pool

The tiles were left to dry off overnight and we came back the next day to seal the floor using two coats of Tile Doctor Colour Grow which is an impregnating sealer that fills up the pores in a tile to protect it from stains whilst enhancing its natural colours.

Quarry Tiled Pool Surround Cambridge During Sealing

The process worked well and you can see the difference in the photographs above however the tricky nature of the environment meant it took longer than usual to complete but the main thing was the customer was happy with the result.

Quarry Tiled Pool Surround Cambridge After Sealing Quarry Tiled Pool Surround Cambridge After Sealing

 
 
Source: Quarry Tiled Pool Surround Cleaned and Sealed in Cambridge

Deep Cleaning Grubby Quarry tiles

This Quarry Tiled Kitchen floor had been laid in 2000 which is relatively recent compared to some of the floors I’m asked to deal with, the tiles are 150 x 150 mm Quarry tiles with a mixture of colours. A customer in Cardiff said that the Quarry tiles has been sealed by the tiler however it wasn’t long after it was completed that the before became very grubby looking. You can see this for yourself in the photograph below where you should be able to make out the ingrained dirt and discoloured tile grout.

Grubby Quarry Tiled Kitchen Floor Cardiff Before Cleaning

Cleaning Quarry Tiles

I set about cleaning the floor with undiluted Tile Doctor Remove and Go mixed 3 to 1 with NanoTech UltraClean which adds tiny abrasive particles to a strong coatings remove; this mixture not only removes any previous sealers but also deep cleans the tiles and brings the grout back to its original colour. I used a rotary machine with a disc shaped scrubbing brush attachment disc which really gets into the dirt. The soiled solution was removed using a wet vacuum, stubborn areas retreated and then the floor was rinsed until all the cleaning solution had been removed.

Grubby Quarry Tiled Kitchen Floor Cardiff During Cleaning

Sealing a Quarry Floor Sealing

The floor was left to dry for 24 hours and I came back later to seal it. Before sealing I used a hand held damp meter to verify the floor had dried. I had previously discussed the choice of sealer with the customer to establish how they wanted the floor to look and selected Tile Doctor Seal and Go for its satin shine.

Grubby Quarry Tiled Kitchen Floor Cardiff During Sealing

I went on to seal the tiles with two coats of Tile Doctor Seal and Go using a water test to verify I had applied the right amount of sealer and that liquids were being repelled from the surface of the tile as opposed being absorbed.

Grubby Quarry Tiled Kitchen Floor Cardiff After Cleaning and Sealing

The floor cleaned up really well especially after sealing which brought the colours in the tile back to life; the customers were delighted with the results.
 
 
Source: Residential and Commercial Tile Cleaning in South Wales

Removing Plaster from Quarry tiles

This floor was another case of builders failing to protect the Quarry Tiled Floor when they were working at this house in Bedford, this is certainly not un-typical of plasters considering the number of messy floors we have had to clean up previously. I guess in some ways we shouldn’t complain as they are keeping us busy but it was my floor I would be quite upset.

Deep Cleaning Quarry Tiles

To get rid of the plaster I applied a solution of Tile Doctor Grout Clean-up which is an acid based product designed to remove grout from the surface of tiles but works equally well on cement, plaster and other mineral deposits such as effloresce and rust. Working in sections the Grout Clean-up was applied, scrubbed in and then washed off, being an acid it’s not advised to leave it on the tile for too long.

Once the plaster was dealt with the whole floor including the tiles and grout was given a good clean using Tile Doctor Pro-Clean which is a strong alkaline product that’s safe to use on Tile, Stone and Grout. For best results leave it to soak into the tile for twenty minutes before giving the tiles a good scrub.

Once the tiles were clean the floor was given a good rinse with clean water to remove any remaining chemical and neutralise the floor before sealing; a wet vacuum was used to remove as much water from the floor as possible so it could dry faster.

Deep Cleaning Quarry Tiles in Bedford Before Deep Cleaning Quarry Tiles in Bedford After

Sealing Quarry Tiles

We left the floor to dry overnight and came back the next day to seal it using four coats of Tile Doctor Seal and Go sealer which adds a nice sheen to the floor as well as providing long term stain protection. The photographs above show the transformation of the floor and certainly the customer was very happy with the result.
 
 
Source: Residential and Commercial Tile Cleaning in Bedfordshire

Restoring old Quarry tiles in Bedford

This was a very straightforward request to clean and seal an old Quarry tiled floor that dated back to the Victorian era. The tiles didn’t appear to have any sealer or other treatment applied, it could be if there was anything it had worn off a long time before.

Cleaning Old Quarry Tiles

A strong dilution of Tile Doctor Pro-Clean was applied to the floor and left to soak into the tile for around twenty minutes before being worked into the floor using a rotary floor scrubber fitted with a black pad. Pro-Clean is a strong alkaline product so unlike acid based cleaners it’s safe to use on any tile and stone which given the age of these tiles was quite an important consideration.

Pro-Clean was also used along the grout lines which were scrubbed by hand using a stiff brush. The floor was then rinsed with clean water which was removed using a wet vacuum and the whole process repeated until we were happy that the tile and grout was clean.

This process took most of the day and before we left the floor was given a thorough rinse with clean water to remove any trace of Pro-Clean as this can upset sealing later on.

Victorian Quarry Tiles Bedford before cleaning Victorian Quarry Tiles Bedford after cleaning and sealing

Sealing Quarry Tiles

The floor was left to dry overnight and when we came back the next day we were able to start the sealing process. For sealing a combination of sealers was used starting with a single coat of Tile Doctor Colour Grow; Colour Grow is a impregnating sealer that fills the pores in the tile in order to repel any contaminates that can stain the floor, it also as its name suggests brings out the colour in the tile. Once this had dried a coat of Tile Doctor Seal and Go was applied which is a topical sealer that adds a nice sheen to the floor. This proved to be a great combination and the quarry tiles looked really nice when they were finished in fact the customer was so surprised by the result we had managed to achieve.
 
 
Source: Residential and Commercial Quarry Tile Cleaning in Bedfordshire

Restoring Quarry tiles hidden under Laminate

This Red and Black Quarry tiled floor was discovered underneath a laminate floor in the hallway of a house built in Cardiff around 1910. The customer was keen to restore it as an original feature and I was confident that despite the damaged tiles, cement and paint we would be able to do so.

Quarry Tiles Before Restoration in Cardiff

Cleaning a Quarry Tiled Floor

The area around the doorway was in the worst condition and unfortunately those tiles were beyond rescue and needed to be replaced which wasn’t a problem as with a bit of research you can usually find what you need.

The next step was to carefully scrape as much cement and old paint off the tile surface as possible by hand and remove the waste; I also tested the floor at this point for dampness at the doorways as its good to know if there are any damp problems that may require additional attention. I then applied undiluted Tile Doctor Remove and Go to the whole floor with a brush agitating as I went, it was left it on for about an hour to break down any old sealers and coatings before being rinsed off with clean water twice which was then hovered up with a wet vacuum.

The next stage was to remove the cement using Tile Doctor Grout Clean-Up which being an acid based products starts to work as soon as it’s applied to the tile, this was worked in using a small hand held scrubbing brush before being given a good rinse down with clean water.

The last step of the cleaning process was to steam clean the tiles to open up the pores and ensure that no trace of cleaning agents was left behind that could upset the sealer.

Quarry Tiles After Restoration in Cardiff

Sealing a Quarry Floor Sealing

The floor was left to dry for two days before and I came back the next day to seal it. Before sealing however I wanted to be use it had dried out sufficiently so I tested it again use a Stanley hand held meter, the previous reading I took proved to be a useful benchmark. Sealing was done using two coats of Tile Doctor Seal and Go which really brought the floor back to life and lifted the lovely colours in the tile. Needless to say the customer was delighted with the restoration of the floor.
 
 
Source: Residential and Commercial Tiled Floor Restoration in South Wales

Cleaning Kitchen Quarry Tiles

This job was to strip and re-seal these Quarry tiles installed in a commercial kitchen which was undergoing refurbishment at a canteen in Rushden, Northamptonshire. The tile finish had dulled and there was a lot of staining to the grout.

Quarry Tiles in Rushden before cleaning

Cleaning Quarry Tiles

As there was little in the way of kitchen units to protect I go straight down to stripping down the floor using a strong dilution of Tile Doctor Pro-Clean which is a multi-purpose cleaner/stripper that’s safe to use on stone, tile and grout. The solution was applied with a mop and left it to dwell on the floor for twenty minutes in order to give it chance to soak into the tile surface and get to work on the existing sealer and dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad and stiff hand brushes were used along the grout lines to get the grout clean. The resulting soiled solution was picked up with a wet and dry vacuum and the floor was then rinsed with clean water to neutralise the tile and stubborn areas re-treated. Once I was happy the floor was given a final rinse and then left to dry overnight ready for sealing the next day.

Sealing Quarry Tiles

After checking the tiles had dried I proceeded to seal the floor using four coats of Tile Doctor Seal and Go which will protect the floor from staining going forward and also adds a nice shine to the tile.

Quarry Tiles in Rushden After cleaning

 
 
Source: Commerical and Residential Quarry Tile floor cleaning services in Northamptonshire

Removing layers of sealer from Quarry Tiles

We were asked to work our magic on these dirty Quarry tiles at a residence in the historic town of Hitchin. The tiles had been sealed on a number of occasions but had not been deep cleaned beforehand which effectively trapped the dirt under the sealer making it difficult to get clean.

Quarry Tiles in Hitchen Before Cleaning

Stripping Quarry Tiles

To get them clean the coatings on the surface of the Quarry tile had to be stripped off back to the original surface. To do this we mixed a dilution of Tile Doctor Remove and Go 50/50 with NanoTech UltraClean and applied it to the floor leaving it to soak in to the tile for around 20 minutes before scrubbing it in with a wire brush. Remove and Go is as its name suggests is a coatings remover which is safe to use on Tile and Stone and is designed to remove most products from, this is assisted by the addition of NanoTech UltraClean which adds tiny abrasive particles into the solution making it more effective. The floor was then scrubbed using a rotary machine fitted with a black scrubbing pad and the grout lines scrubbed by hand using a stiff brush. The floor was then rinsed with water which was removed using a wet vacuum. The process was then repeated until we were happy that the tile and grout was clean and that the old sealer had been removed, again the floor down and being the last time washed down thoroughly as traces of cleaning products can upset sealers later on.

Sealing Quarry Tiles

Once happy with the floor and it had time to dry off it was sealed with four coats of Tile Doctor Seal and Go sealer adds a nice sheen to the floor as well as adding long term stain protection; needless to say the customer was very happy with the results.

Quarry Tiles in Hitchen After Cleaning and Sealing

 
 
Source: Quarry Tile Cleaning Services in Hitchin

Cleaning kitchen Quarry Tiles in Northamptonshire

Apologies for the poor quality of these grainy Quarry Tile Cleaning photographs taken in the kitchen of a residential property in Daventry but it was the middle of winter and I was using my phone camera which doesn’t have an effective flash. Hopefully you can see from the photograph below how dirt had become ingrained into the tile and stains to the grout.

Quarry Tiled Kitchen Floor Before Cleaning

Cleaning Quarry Tiles

To get the floor clean I removed the kick boards around the base of the kitchen units and applied a dilution of Tile Doctor Pro-Clean mixed with NanoTech Ultraclean which adds tiny abrasive particles to an already powerful alkaline cleaning product that is safe to use on tile and stone. It was applied with a mop and left it to dwell on the floor for twenty minutes first in order to give it chance to soak into the tile and get to work on the dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad, stiff hand brushes were along the grout lines. The soiled solution was picked up with a wet and dry vacuum and the floor was then rinsed with clean water to neutralise the tile and allow us to see which areas need further attention. Once I was happy the floor was given a final rinse and then left to dry overnight ready for sealing the next day.

Quarry Tiled Kitchen Floor During Cleaning

Sealing Quarry Tiles

On my return the floor was checked in a number of places with a damp meter to confirm it had dried which it had and it was then sealed using numerous coats of Tile Doctor Seal and Go which adds a nice shine to the floor as well as providing a surface seal that will help protect the tile from stains going forward. Sealing can take some time as you need to let the first coat dry before starting the second.

Quarry Tiled Kitchen Floor After Cleaning and Sealing

 
 
Source: Quarry Tile Cleaning Services in Northamptonshire

Cleaning Old Quarry Tiles in a Barn Conversion

A while ago I was asked to quote to clean up an old quarry tiled floor in a converted barn in Ashtead. Whilst I was there I carried out a test patch for the lady to show what the results would be; she had said that if she wasn’t satisfied she was going to replace the floor so she must have met her expectations as a week later we were given the go ahead to carry out the work.

Quarry Tile Cleaning Ashtead before

Quarry Tile Cleaning Ashtead before2

Cleaning Hallway Quarry Tiles

Fortunately for us they had recently removed the old kitchen and scheduled us after to clean the quarry tiles before completing the decorating and refitting a new kitchen. We cleaned the tiles using a mixture of Tile Doctor Pro-Clean diluted 1:4 parts with water and Nanotech Ultraclean which adds tiny abrasive particles into the cleaning solution. Normally I would work this into the floor using a black scrubbing pad however the floor was very uneven so I used a medium nylon brush on my rotary machine instead, this had the added advantage of reaching into the grout as well. I should mention we thoroughly rinsed the floor as we went along using a wet vacuum to remove the soiled solution. It took two of us two days to scrub the areas that had to be done and we had a blower running to help dry out the floor.

Sealing Hallway Quarry Tiles

We returned three days later and carried out moisture test to ensure the floors were dry and ready to be sealed. The Quarry tiles were then sealed them with five coats of Tile Doctor Colour Grow which is an impregnating sealer that reaches into the pores of the tile and lifts the natural colours. The owner was extremely happy with the floor and couldn’t wait to have her new kitchen installed to see how it would look.

Quarry Tile Cleaning Ashtead after

Quarry Tile Cleaning Ashtead after2

 
 
Source: Quarry Tile Restoration in Surrey

School Quarry Tile and Grout Refurbished

Before and after photograph below of a Quarry Tiled floor at a school in Dunstable that was in such a bad state we had to apply grout colourant to the floor. Quarry tiles are fairly indestructible so ideal for use in schools etc. where they will see a lot of foot traffic and abuse, having said that they will fade with wear over time and naturally the grout can become ingrained with dirt if not protected.

Cleaning Quarry Tiles

It had been a while since the Quarry Tiles and Grout had been given a really deep clean to so we mixed a dilution of Tile Doctor Pro-Clean 50/50 with NanoTech UltraClean and applied it to the floor and left to soak in for around 10 minutes; Pro-Clean is a multipurpose alkaline cleaning product designed specifically for cleaning tile and stone and NanoTech UltraClean adds tiny abrasive particles into the solution to make a more effective cleaner. The floor was then scrubbed using a rotary machine fitted with a black scrubbing pad and the grout lines scrubbed by hand using a stiff brush. The floor was then rinsed thoroughly with water which was removed using a wet vacuum, once the Quarry tiles were dry it was possible to spot the areas in need of further attention and these were scrubbed by hand together with more of the Pro-Clean/UltraClean mix and a steamer. At this stage it became apparent that that although the grout had improved it was too far gone and never going to make the grade and either needed to re-done or as per our suggestion re-coloured.

Grout Colouring

For floor grout we always recommend the use of an epoxy grout colouring product which not only completely covers the grout making it look new again but also provides a permanent barrier that prevents the grout from staining in future. They can be quite time consuming to apply however especially if you have a small format Quarry tile with lots of grouting.

Sealing Quarry Tiles

Once happy with the floor and it had time to dry off it was sealed with six coats of Tile Doctor High Shine Sealer which will provide future surface stain protection and also leaves a nice deep shine on the floor. It took a long time but I think you will agree from the before and after photograph below we managed quite a transformation.


 
 

Tired Quarry Tiled floor restored in Dunstable School

Restoring Quarry Tiles in Cambridge

These photographs are from a Quarry Tile Cleaning job we did for a house owner in Cambridge, I’m afraid my photographs are not the best but I think you can see how the Quarry tiles were looking discoloured and worn.

Quarry Tiled Floor Cambridge Before

Cleaning Kitchen Quarry Tiles

Working in sections the floor was wetted with a dilution of Tile Doctor Pro-Clean combined 50/50 with Nanotech UltraClean, these two products combine to make a powerful and effective cleaning solution that’s safe to use on tile and stone. The solution was left to soak into the tile for twenty minutes whilst we got our machinery ready.

It helps if you have the right tools for the job and in this case we fitted a scrubbing pad to a rotary buffing machine and working the cleaning solution into the floor to scrub away the ingrained dirt. The machine can struggle to get into the grout lines so these need to be scrubbed by hand using a stiff brush and more cleaning solution. Once the floor was clean the soiled solution was picked up using a wet and dry vacuum and then washed down with clean water to remove any trace of chemical. This revealed a few stubborn areas that needed further work so these were re-treated and the floor washed down again and then left to dry overnight.

Sealing Kitchen Quarry Tiles

We came back the next day to seal the floor and after checking the tiles had indeed dried we proceeded to apply Tile Doctor Seal and Go which is a water based sealer (no smell) that really brings out the shine and colour in Quarry tiles. Around five coats were sufficient and once it had dried the floor was transformed.

Quarry Tiled Floor Cambridge After

 
 
Source: Quarry Tile Renovation in Cambridge

Transforming old Victorian Quarry Tiles

These old red and black Victorian quarry tiles at a house in Leek, Staffordshire, were in a bit of a state as you can see from the photographs below.

Quarry Tiles Before Cleaning Quarry Tiles Before Cleaning

Cleaning old Quarry Tiles

To clean the floor I applied a 50/50 mix of Tile Doctor Pro-Clean and NanoTech Ultra Clean diluted with water which was left to soak into the floor and then worked into the tile using a rotary machine fitted with a black scrubbing pad running at a slow speed. Pro-Clean is a strong alkaline cleaner and NanoTech Ultra Clean adds tiny abrasive particles to the solution that can help lift out the dirt.

After cleaning it I noticed that in places it was not as clean as I would of liked it, so to improve it further it necessary to get on my hands and knees and scrub them with a stronger dilution of the Pro-Clean and NanoTech UltraClean solution and a small black pad. This did the trick and so final step was to neutralise the floor tiles ready for sealing by giving them a good wash with clean water and then left it overnight to dry. A Wet Vacuum comes in handy during this process for removing fluids from the floor

Sealing old Victorian Quarry Tiles

The next day I wiped it over with a damp mop to get any dirt or dust that might have settled overnight and then when it was dry again I applied four coats of Tile Doctor Seal & Go using an air mover to help dry the floor quicker between coats.

Quarry Tiles After Cleaning Quarry Tiles After Cleaning

Seal and Go adds a nice low shine to the tile and as you can see the floor looked amazing afterwards, needless to say the customer was very pleased with the transformation and left the comment below.

“I found Trevor a very professional and dedicated workman. He would not let the job finish until he had got the best result.
Miss Jackie Spencer, Leek”

Quarry Tiles After Cleaning Quarry Tiles After Cleaning

 
 
Source: Restoring old Quarry Tiles in Staffordshire

Restoring Quarry Tiles in South London

I recently completed this Quarry Tile restoration work for a young couple in Grove Park, South London. They were refurbishing their property and wanted to keep as much of the original features that they could. In the kitchen they had the original quarry tiles and had attempted to clean the floor themselves but we’re unsuccessful. I quoted for the job and took time to explain the process and which products I would be using.

They contacted me a couple of days later to let me know that they wanted me to carry out the work which was gratifying as I had put a lot of time into the quote. Turns out I got the job because they could see I knew what I was talking about giving them confidence I could do the work and another company had quoted twice the price I gave them and didn’t even pop round to carry out a site survey.

Quarry Tile Cleaning Before Quarry Tile Cleaning Before

Cleaning Hallway Quarry Tiles

I turned up at the agreed time and set about by cleaning the floor with a mixture of Tile Doctor Pro-Clean and NanoTech UltraClean which combine well together to produce a very effective cleaning product that is safe to use on tile and stone. The solution was worked into the floor using a rotary scrubbing machine fitted with a black scrubbing pad; after a while the soiled solution was removed using a wet vaccum and the floor was given a thorough rinse with clean water to see what I had left to deal with.

What was left was a mixture of paint, grease and sticky residues from old carpet tape and if that wasn’t enough there were limescale deposits. To tackle this a stronger product was required so I laid down Tile Doctor Remove and Go and left it to dwell on the tile for about 45 minutes which was sufficient to break down the stubborn marks and allow for them to be scrubbed out. Remove and Go is a strong coatings remover which as its name suggests should remove just about anything and with the exception of the limescale it lived up to its name.

I think it’s a fair statement to say that Tile Doctor have a product to treat every problem and to remove the limescale I used Tile Doctor Grout Clean-Up which is an acid based product usually used to remove excess grout but it’s also effective on the removal of mineral deposits; needless to say it removed the limescale without a problem. You do have to be very careful when using strong products like these on tile so I only left it on the floor long enough to do the job.

The last step was to fit a brush head onto my rotary floor machine and gave the floor a thorough rinse neutralising the floor and making sure that all trace of cleaning products were removed. Once I had finished I locked up the house and left the floor to dry for several days.

Sealing Hallway Quarry Tiles

When I returned I first checked that the floor was dry enough to seal using a moisture meter. The floor was dry so we started the process of sealing the floor with Tile Doctor Seal and Go, the Quarry Tiles were very porous and it tool seven coats of sealer before the tiles were completely sealed. Seal and Go was chosen as the customer wanted liked the low sheen finish this sealer provides whilst also offering excellent stain protection.

Quarry Tile Cleaning After Quarry Tile Cleaning After

The owners were absolutely delighted with the results and they put in a fantastic review about me on the Tile Doctor website.

“Bill Bailey provided an extremely professional and high quality service from first point of contact to end result. He took time to assess the tiles to be cleaned and approached the job with a genuine commitment to get it right and achieve the best possible results. He carefully explained all the processes involved and was able to answer all our questions and provide advice. We would not hesitate to recommend him very highly. Gemma, London

Quarry Tile Cleaning Before and After

 
 
Source: Putting the life back into old Quarry Tiles in London

Maintaining Old Quarry floor tiles

Customer had these Dennis Ruabon Quarry Tiles fitted over 20 years ago in the WC of his house in Low Bentham, various cleaning and sealing products have been used since however this left a build-up of contamination on the Tiles which was detrimental to their aesthetic appeal and also left a noticeable residue smell.

Black Quarry Tiles Before Black Quarry Tiles Before

Cleaning Quarry Tiles

To clean the Tiles and strip off previous sealing coatings we used Tile Doctor Pro-clean diluted 1 to 10 with warm water. This was left to dwell on the floor for a while before being worked into the tile using and black buffer pad fitted to a rotary buffing machine. The whole area was cleaned in this manner along with a stiff hand brush to get into the grout lines and a wet vacuum which was used to suck up the dirty residue before the floor was rinsed down with cold water. The wet vacuum was used again to remove the water, one tile was loose so this was re-fixed and the floor left to dry.

Sealing Quarry Tiles

Once the floor was fully dry we applied two coats of Tile Doctor Colour Grow which will protect it going forward and also helps to bring out the colour in the tile whilst maintaining a more natural appearance. There were some stubborn stains and discolouration on the tiles that could not be treated however I think you will agree it is much improved and you will have to take my word for this but it also smells better

Black Quarry Tiles After Black Quarry Tiles After

Before leaving we left the customer with a bottle of Tile Doctor Neutral cleaner, this product is recommended for sealed floors due to its very low PH formula; there are a number of acidic floor cleaning products available which should not be used with stone or sealed floors as the acid will eat into the seal or stone surface over time reducing its life.
 
 
Source: Cleaning and Sealing Dennis Ruabon Quarry tiles in Lancashire

Maintaining Quarry Tiled Hallway

These photographs are from a Quarry Tile Cleaning job we did for a lady in Brixton recently, as you can see from the early pictures they were not only dirty but there was also evidence of an old sealer and splashes of paint on them as well both of which would have to be removed first.

Cleaning Hallway Quarry Tiles

The first task we did on arrival was to disconnect her cooker and washing machine which were placed outside in the garden, this would allow us to get at all the tiled areas and also meant there was less to protect.

Working in small sections the next step was to pre-wet the floor tiles followed by adding a dilution of Tile Doctor Remove and Go combined 50/50 with Nanotech UltraClean, these two products combine to make a powerful cleaner/stripper that’s safe to use on tile. The cleaning solution was left to soak into the tile whilst we set up all of our equipment and added protective coverings to the kitchen units, walls and adjoining floors.

After about forty five minutes we re-wet the areas and hand scrubbed the tiles using scouring pads. This process was repeated covering small areas at a time until the kitchen was finished. We then used our scrubbing machine with a medium brush head fitted and thoroughly rinsed the floor to remove any trace of chemical.

We needed the floor dry for sealing so a couple of Turbo blowers we setup to force dry the floor and this took a couple of hours before my moisture meter told me that the floor was dry enough.

Sealing Hallway Quarry Tiles

After discussing sealer choices with the customer it was decided to seal the floor with Tile Doctor Colour Grow which provides a natural finish whilst lifting the natural colours in the tile. Two coats were sufficient and once it had dried we refitted the cooker and washing machine, put all the plinths back and removed all of our protective coverings.

The lady was really pleased with our work and left the following testimonial.

“Bill did a fantastic job on my kitchen floor, I can’t thank him enough. Mrs Scott, Brixton”
 
 
Source: Cleaning and sealing a Quarry Tiled floor tiles in Surrey

Worst Grout Haze Removed From Quarry Tiled Patio

This customer based in New Cross South East London had a significant problem with their patio. Their home is a period Victorian property so when choosing a stone for the patio, they bought reclaimed quarry tiles to marry up with the period of the house, and proceeded with their DIY project. Unfortunately they were not aware that quarry tiles are porous until sealed, and grout left on the tile and not wiped off immediately, will leave a grout haze or in this case stick to the tile altogether.

I inspected the tiles and confirmed this was the worst case of grout haze I had ever seen; un-deterred I proceeded to carry out a test clean (you can see this reflected in the video above) and this demonstrated successfully that the tiles could be restored.

Cleaning Patio Quarry Tiles

Satisfied with the results of the test clean I proceeded to clean the rest of the floor. For this I used Tile doctor Grout Clean-Up which contains concentrated acid and is designed to penetrate below the surface to remove grout smears; this was diluted 1 to 1 with water which is a very strong mix. I sprayed the solution onto the tiles, working 1sqm at a time, leaving it to dwell on the tiles for a few minutes before scrubbing the tiles by hand with a rough pan cleaner. I then rinsed the area off with water and used my wet vac to remove the soiled solution. The strong mix had the desired effect on the Quarry tiles but it was necessary to go over the area again after spotting some of the worse stains the first application had missed. Happy with the result, I carried out this process across the rest of the patio, working 1 sqm at a time.

Sealing Kitchen Quarry Tiles

When I was finished the customer was very happy with the result, and now had a patio they could use. The customer was keen to carry on with their DIY project, and wanted to seal the patio themselves, so I advised them to use Tile Doctor Colour Grow, which is a colour intensifier and impregnated sealer; this will both protect and enhance the reclaimed quarry tile into the future.
 
 
Source: Removal of grout haze from reclaimed Quarry Tiles on a Patio

Removal of Grout Haze on a Quarry Tiled Floor

These photographs are from a recently laid Quarry tiled floor in Woodford. East London where the tiler had smothered the tiles with grout and left it on the surface too long where it had then dried and he was unable to remove it. Unable to rectify the problem the Quarry tiles were then sealed, I suspect this was in an attempt to improve the look of the floor which unfortunately left it looking quite the opposite.

Quarry Tiles with Grout Haze

Remove Grout Haze and Cleaning Quarry Tiles

Undeterred by the state of the floor which we were confident could be put right we took the job on. The first step was to remove the sealer by using a strong dilution of Tile Doctor Pro-Clean mixed 3 parts water to 1 part Pro-Clean. This was left to dwell on the tile surface for ten minutes before scrubbing with black pads fitted to a rotary scrubbing machine.

Removing Grout Haze

Once we were happy the sealer had been removed we could tackle the Grout Haze with Tile Doctor Grout Clean-Up. It’s applied to the tile surface and again scrubbed in with black scrubbing pads. There was a lot of grout haze so the processes had to be repeated; all the edges were done on hands and knees with small doodle bug pads. Once the haze was removed we washed the floor three times with water to remove any residue.

Quarry Tile During Cleaning Quarry Tiles with Partial Grout Haze

The dirty solution was removed using a wet vacuum and the floor was rinsed three times to remove the residue and neutralise it, the floor was then left for 48 hours to allow it dry fully prior to sealing.

Sealing Quarry Tiles

When we returned we sealed the Quarry tiles using Tile Doctor Seal and Go which is recommended for sealing quarry tiles and give’s a nice low sheen effect. Five coats of sealer where needed in total which took some time to apply as you have to let the sealer dry before applying the next coat.

Quarry Tiles Cleaned and Sealed

The result was a very satisfied customer.
 
 
Source: Quarry Floor Cleaning and Sealing in Woodford, Essex

Quarry tile refresh in Leicestershire

Details below of a Quarry Tiled kitchen floor installed in a house in the Leicestershire village of Croft. The floor was very old and heavily soiled with some paint spots and the quarry tiles were looking dull and tired, there was some staining to the grout.

Croft Quarry Tiles Before Cleaning

Cleaning Kitchen Quarry Tiles

A solution of Tile Doctor Pro-Clean was applied to the floor and left to soak for a short while before being scrubbed in with a rotary machine fitted with a black scrubbing pad. The grout also need attention, unfortunately we don’t have a machine that will get into the grout lines so this had to be manually scrubbed by hand using a grout brush, which as you can imagine took some time to do. The soiled cleaning solution was then removed using a wet vacuum and the floor thoroughly rinsed with water and then left to dry overnight.

Sealing Kitchen Quarry Tiles

When we returned the next day we could see there were some grout lines that we had missed the day before so we set about cleaning those up. Once we were happy with the floor it and it had managed to dry off we sealed the floor using five coats of Tile Doctor Colour Grow which provides surface stain protection to the quarry tile and grout and also brings out the colour in the surface of the tile.

Croft Quarry Tiles After Cleaning and Sealing

 
 
Source: Quarry Tile Cleaning in Leicestershire

Neglected Victorian Quarry Tiles Transformed

We were asked to restore this Original Victorian Quarry tiled floor following a major refurbishment of a Grade 1 listed mansion in Pangbourne, Berkshire. The tiles has seen many years of neglect and as you can see from the photo below it was not given much thought or care by the builders and decorators who had been working on the property.

Neglected Victorian Quarry Tiles

Cleaning Victorian Quarry Tiles

We set about stripping and cleaning the floor of all the paint and dirt that had been left to accumulate on its surface over the years starting with a strong dilution of Tile Doctor Pro-Clean worked into the Quarry tiles using a rotary machine fitted with a black scrubbing pad. This was removed using a wet and dry vacuum and followed by hours of detailed cleaning using Tile Doctor Remove and Go mixed 50/50 with NanoTech Ultra Clean which adds Nano sized abrasive particles to the solution to make a more effective coatings remover. We allowed this to dwell for a short while before agitating it with a rotary machine again fitted with a black scrubbing pad working the solution into the floor, this treatment tackled the stubborn paint and all sorts of other residues. Once we were happy with floor it was given a good rinse down with clean water and then left to dry.

Refurbished Victorian Quarry Tiles

Sealing Quarry Tiles

Once the Quarry Tiles were dry we set about sealing them, a low sheen finish was required so four coats of Tile Doctor Seal and Go were applied, it’s a water based sealer that will protect the surface going forward. The Main contractor could not believe we managed to get the floor looking pristine and back to its original condition.
 
 
Source: Transforming a neglected Victorian Quarry Tiled floor in Berkshire