Photographs below of a job we did cleaning and sealing the Quarry Tiles surrounding a residential indoor swimming pool floor tiles at a grand residence in Cambridge. As you can see from the photograph below the Quarry tiles and Grout was looking rather washed out and given their proximity to the pool extra care was needed to be ensure we didn’t contaminate the pool with dirty water from the cleaning process or chemicals, fortunately all our equipment is electrically isolated so that was not a problem.
Swimming Pool Tile Cleaning
Fortunately the pool was fitted with a cover so we made a start cleaning the tiles using a strong dilution of Tile Doctor Pro-Clean mixed 50/50 with NanoTech Ultra Clean which add tiny abrasive particles into the cleaning solution making it more effective. Working in sections the solution was left to soak into the tile and grout before being worked into the floor using a rotary machine fitted with a scrubbing pad running at slow speed to reduce splashing. This process removed any remaining sealer and cleaned the tile and grout up nicely, we used clean water to rinse the floor and a wet vacuum to remove the soiled solution making sure not to drain any solutions into the pool and re-treating any stubborn areas. This process was fairly tedious and took up much of the day but the results were well worth the effort.
Sealing Quarry Tiles around a Pool
The tiles were left to dry off overnight and we came back the next day to seal the floor using two coats of Tile Doctor Colour Grow which is an impregnating sealer that fills up the pores in a tile to protect it from stains whilst enhancing its natural colours.
The process worked well and you can see the difference in the photographs above however the tricky nature of the environment meant it took longer than usual to complete but the main thing was the customer was happy with the result.
This job was to strip and re-seal these Quarry tiles installed in a commercial kitchen which was undergoing refurbishment at a canteen in Rushden, Northamptonshire. The tile finish had dulled and there was a lot of staining to the grout.
Cleaning Quarry Tiles
As there was little in the way of kitchen units to protect I go straight down to stripping down the floor using a strong dilution of Tile Doctor Pro-Clean which is a multi-purpose cleaner/stripper that’s safe to use on stone, tile and grout. The solution was applied with a mop and left it to dwell on the floor for twenty minutes in order to give it chance to soak into the tile surface and get to work on the existing sealer and dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad and stiff hand brushes were used along the grout lines to get the grout clean. The resulting soiled solution was picked up with a wet and dry vacuum and the floor was then rinsed with clean water to neutralise the tile and stubborn areas re-treated. Once I was happy the floor was given a final rinse and then left to dry overnight ready for sealing the next day.
Sealing Quarry Tiles
After checking the tiles had dried I proceeded to seal the floor using four coats of Tile Doctor Seal and Go which will protect the floor from staining going forward and also adds a nice shine to the tile.
Apologies for the poor quality of these grainy Quarry Tile Cleaning photographs taken in the kitchen of a residential property in Daventry but it was the middle of winter and I was using my phone camera which doesn’t have an effective flash. Hopefully you can see from the photograph below how dirt had become ingrained into the tile and stains to the grout.
Cleaning Quarry Tiles
To get the floor clean I removed the kick boards around the base of the kitchen units and applied a dilution of Tile Doctor Pro-Clean mixed with NanoTech Ultraclean which adds tiny abrasive particles to an already powerful alkaline cleaning product that is safe to use on tile and stone. It was applied with a mop and left it to dwell on the floor for twenty minutes first in order to give it chance to soak into the tile and get to work on the dirt. It was then worked into the floor using a rotary machine fitted with a black scrubbing pad, stiff hand brushes were along the grout lines. The soiled solution was picked up with a wet and dry vacuum and the floor was then rinsed with clean water to neutralise the tile and allow us to see which areas need further attention. Once I was happy the floor was given a final rinse and then left to dry overnight ready for sealing the next day.
Sealing Quarry Tiles
On my return the floor was checked in a number of places with a damp meter to confirm it had dried which it had and it was then sealed using numerous coats of Tile Doctor Seal and Go which adds a nice shine to the floor as well as providing a surface seal that will help protect the tile from stains going forward. Sealing can take some time as you need to let the first coat dry before starting the second.
A customer from Kendal (famous for its Kendal Mintcake) called me in to look at their Quarry Tiled Utility floor, which was looking very dirty and stained. On inspection the sealer had broken down and was no longer protecting the tile resulting in dirt getting ingrained into the pores of the tile resulting in discolouration. We agreed what short of finish was required and the customer booked me in to do the work.
Cleaning Quarry Floor Tiles
My first job was to protect the surrounding areas from splashes so on my arrival I covered the wooden floor in the hallway before starting to remove the old sealer with Tile Doctor Remove and Go, I sprayed it on working in small areas leaving it to dwell for a while before scrubbing it in with a stiff brush making sure I scrubbed it in well before removing the soiled solution with a wet vacuum. I scrubbed all the grout joints at this point to make sure they were all clean and then washed the floor down to remove any chemical and neutralise the floor. It was a relatively small floor so I left it to dry and returned a few house later to seal it.
Sealing Quarry Floor Tiles
On my return I used a damp tester to make sure the floor was dry, which it was, so I sealed it with two coats of Tile Doctor Colour Grow which is a as well as protecting the floor brings the natural colours out in the tile. Naturally if the damp tester had showed that it was damp I would not have sealed the floor that day as the sealer would not have taken properly.
This job took me one day as it was only a very small floor and I was able to seal it in the same day the customer were happy with the result I went through the maintenance program and explained how to clean the floor.
Before and after photograph below of a Quarry Tiled floor at a school in Dunstable that was in such a bad state we had to apply grout colourant to the floor. Quarry tiles are fairly indestructible so ideal for use in schools etc. where they will see a lot of foot traffic and abuse, having said that they will fade with wear over time and naturally the grout can become ingrained with dirt if not protected.
Cleaning Quarry Tiles
It had been a while since the Quarry Tiles and Grout had been given a really deep clean to so we mixed a dilution of Tile Doctor Pro-Clean 50/50 with NanoTech UltraClean and applied it to the floor and left to soak in for around 10 minutes; Pro-Clean is a multipurpose alkaline cleaning product designed specifically for cleaning tile and stone and NanoTech UltraClean adds tiny abrasive particles into the solution to make a more effective cleaner. The floor was then scrubbed using a rotary machine fitted with a black scrubbing pad and the grout lines scrubbed by hand using a stiff brush. The floor was then rinsed thoroughly with water which was removed using a wet vacuum, once the Quarry tiles were dry it was possible to spot the areas in need of further attention and these were scrubbed by hand together with more of the Pro-Clean/UltraClean mix and a steamer. At this stage it became apparent that that although the grout had improved it was too far gone and never going to make the grade and either needed to re-done or as per our suggestion re-coloured.
For floor grout we always recommend the use of an epoxy grout colouring product which not only completely covers the grout making it look new again but also provides a permanent barrier that prevents the grout from staining in future. They can be quite time consuming to apply however especially if you have a small format Quarry tile with lots of grouting.
Sealing Quarry Tiles
Once happy with the floor and it had time to dry off it was sealed with six coats of Tile Doctor High Shine Sealer which will provide future surface stain protection and also leaves a nice deep shine on the floor. It took a long time but I think you will agree from the before and after photograph below we managed quite a transformation.
These photographs are from a Quarry Tile Cleaning job we did for a house owner in Cambridge, I’m afraid my photographs are not the best but I think you can see how the Quarry tiles were looking discoloured and worn.
Cleaning Kitchen Quarry Tiles
Working in sections the floor was wetted with a dilution of Tile Doctor Pro-Clean combined 50/50 with Nanotech UltraClean, these two products combine to make a powerful and effective cleaning solution that’s safe to use on tile and stone. The solution was left to soak into the tile for twenty minutes whilst we got our machinery ready.
It helps if you have the right tools for the job and in this case we fitted a scrubbing pad to a rotary buffing machine and working the cleaning solution into the floor to scrub away the ingrained dirt. The machine can struggle to get into the grout lines so these need to be scrubbed by hand using a stiff brush and more cleaning solution. Once the floor was clean the soiled solution was picked up using a wet and dry vacuum and then washed down with clean water to remove any trace of chemical. This revealed a few stubborn areas that needed further work so these were re-treated and the floor washed down again and then left to dry overnight.
Sealing Kitchen Quarry Tiles
We came back the next day to seal the floor and after checking the tiles had indeed dried we proceeded to apply Tile Doctor Seal and Go which is a water based sealer (no smell) that really brings out the shine and colour in Quarry tiles. Around five coats were sufficient and once it had dried the floor was transformed.
These old red and black Victorian quarry tiles at a house in Leek, Staffordshire, were in a bit of a state as you can see from the photographs below.
Cleaning old Quarry Tiles
To clean the floor I applied a 50/50 mix of Tile Doctor Pro-Clean and NanoTech Ultra Clean diluted with water which was left to soak into the floor and then worked into the tile using a rotary machine fitted with a black scrubbing pad running at a slow speed. Pro-Clean is a strong alkaline cleaner and NanoTech Ultra Clean adds tiny abrasive particles to the solution that can help lift out the dirt.
After cleaning it I noticed that in places it was not as clean as I would of liked it, so to improve it further it necessary to get on my hands and knees and scrub them with a stronger dilution of the Pro-Clean and NanoTech UltraClean solution and a small black pad. This did the trick and so final step was to neutralise the floor tiles ready for sealing by giving them a good wash with clean water and then left it overnight to dry. A Wet Vacuum comes in handy during this process for removing fluids from the floor
Sealing old Victorian Quarry Tiles
The next day I wiped it over with a damp mop to get any dirt or dust that might have settled overnight and then when it was dry again I applied four coats of Tile Doctor Seal & Go using an air mover to help dry the floor quicker between coats.
Seal and Go adds a nice low shine to the tile and as you can see the floor looked amazing afterwards, needless to say the customer was very pleased with the transformation and left the comment below.
“I found Trevor a very professional and dedicated workman. He would not let the job finish until he had got the best result.
Miss Jackie Spencer, Leek”